On the air http://www.robert-e-roy.com/blog All about building a flying machine with eyes Sat, 19 May 2012 05:36:38 +0000 en hourly 1 http://wordpress.org/?v=3.3.2 well does anything go to feedburner? http://www.robert-e-roy.com/blog/well-does-anything-go-to-feedburner/ http://www.robert-e-roy.com/blog/well-does-anything-go-to-feedburner/#comments Sat, 19 May 2012 05:36:38 +0000 robroy http://www.robert-e-roy.com/blog/?p=470 This is a post to see if anyone gets my posts via feedburner
go googol

]]> http://www.robert-e-roy.com/blog/well-does-anything-go-to-feedburner/feed/ 0 Flying Robots Deliver Tacos http://www.robert-e-roy.com/blog/flying-robots-deliver-tacos/ http://www.robert-e-roy.com/blog/flying-robots-deliver-tacos/#comments Fri, 23 Mar 2012 18:12:12 +0000 robroy http://www.robert-e-roy.com/blog/?p=467 http://tacocopter.com/

Get a taco from your phone
That’s a new idea

]]> http://www.robert-e-roy.com/blog/flying-robots-deliver-tacos/feed/ 0 DROIDWORX V3 QUADROCOPTER AD-4 KIT $2,181.83 http://www.robert-e-roy.com/blog/droidworx-v3-quadrocopter-ad-4-kit-2181-83/ http://www.robert-e-roy.com/blog/droidworx-v3-quadrocopter-ad-4-kit-2181-83/#comments Thu, 15 Mar 2012 07:44:53 +0000 robroy http://www.robert-e-roy.com/blog/?p=455 DESCRIPTION link
This is a kit to build a Mikrokopter in the 48cm class. As a control board is a FlightCtrl ME 2.1 in the set included. Powerful engine – combination: 2200mAh LiPo (4s), 10″ propellers and 2827-35 Motor.

Besides the standard components, the necessary parts such as cables, shrink tubing, etc. are also included.

Thus, the building is almost ‘out of the box’ possible. Through the use of Roxxy engines in this set the MikroKopter is quiet and has low vibriations. IMPORTANT: No receiver is included. Please order desired receiver separately! Delivered products may differ from the picture – note the delivery!

Box / Kit Contents

  • 1x preassembled FlightCtrl ME V2.1
  • Altitude Sensor
  • 4x preassembled BL-Ctrl V2.0
  • 1x Quadro power distribution board
  • 1x MKUSB
  • 1x Droidworx V3 AD-4 frame kit
  • 1x Droidworx standard landing gear
  • 1x Lipo 2200mAh/4s
  • 2x pairs EPP1045 propeller
  • 4x Roxxy 2827-35 – black Brushless Motors
  • 1x connection cable for receiver
  • 1x extensive set of cables
  • Data cable (twisted pair cable – no silicone wire)
  • 4x vibration dampers M3x15
  • Heat shrink tubing for other solder joints
  • 2 pieces of Velcro stripes to fasten Lipo
  • 4 pcs Flex LED Tape for lighting
  • 100 cable ties (black)

Dimmensions:

  • Length–675mm
  • Width–675mm
  • Height–310mm
]]> http://www.robert-e-roy.com/blog/droidworx-v3-quadrocopter-ad-4-kit-2181-83/feed/ 0